| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Tries to shorten the refname to a non-ambiguous name.
Szeder Gábor noticed that the git bash completion takes a
tremendous amount of time to strip leading components from
heads and tags refs (i.e. refs/heads, refs/tags, ...). He
proposed a new atom called 'refbasename' which removes at
most two leading components from the ref name.
I myself, proposed a more dynamic solution, which strips off
common leading components with the matched pattern.
But the current bash solution and both proposals suffer from
one mayor problem: ambiguous refs.
A ref is ambiguous, if it resolves to more than one full refs.
I.e. given the refs refs/heads/xyzzy and refs/tags/xyzzy. The
(short) ref xyzzy can point to both refs.
( Note: Its irrelevant whether the referenced objects are the
same or not. )
This proposal solves this by checking for ambiguity of the
shorten ref name.
The shortening is done with the same rules for resolving refs
but in the reverse order. The short name is checked if it
resolves to a different ref.
To continue the above example, the output would be like this:
heads/xyzzy
xyzzy
So, if you want just tags, xyzzy is not ambiguous, because it
will resolve to a tag. If you need the heads you get a also
a non-ambiguous short form of the ref.
To integrate this new format into the bash completion to get
only non-ambiguous refs is beyond the scope of this patch.
Signed-off-by: Bert Wesarg <bert.wesarg@googlemail.com>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
|
|
Converts tests between t3600-t6300.
Signed-off-by: Nanako Shiraishi <nanako3@lavabit.com>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
|
|
If you have a tag with a single, incomplete line as its payload, asking
git-for-each-ref for its %(body) element accessed a NULL pointer.
Signed-off-by: Junio C Hamano <gitster@pobox.com>
|
|
Previously, we did a sanity check by doing for-each-ref
using each possible format atom. However, we never checked
the actual output produced by that atom, which recently let
an obvious bug go undetected for some time.
While we're at it, also clean up a few '!' into
test_must_fail.
Signed-off-by: Junio C Hamano <gitster@pobox.com>
|
|
As a general principle, we should not use "git diff" to validate the
results of what git command that is being tested has done. We would not
know if we are testing the command in question, or locating a bug in the
cute hack of "git diff --no-index".
Rather use test_cmp for that purpose.
Signed-off-by: Junio C Hamano <gitster@pobox.com>
|
|
Originally, test_expect_failure was designed to be the opposite
of test_expect_success, but this was a bad decision. Most tests
run a series of commands that leads to the single command that
needs to be tested, like this:
test_expect_{success,failure} 'test title' '
setup1 &&
setup2 &&
setup3 &&
what is to be tested
'
And expecting a failure exit from the whole sequence misses the
point of writing tests. Your setup$N that are supposed to
succeed may have failed without even reaching what you are
trying to test. The only valid use of test_expect_failure is to
check a trivial single command that is expected to fail, which
is a minority in tests of Porcelain-ish commands.
This large-ish patch rewrites all uses of test_expect_failure to
use test_expect_success and rewrites the condition of what is
tested, like this:
test_expect_success 'test title' '
setup1 &&
setup2 &&
setup3 &&
! this command should fail
'
test_expect_failure is redefined to serve as a reminder that
that test *should* succeed but due to a known breakage in git it
currently does not pass. So if git-foo command should create a
file 'bar' but you discovered a bug that it doesn't, you can
write a test like this:
test_expect_failure 'git-foo should create bar' '
rm -f bar &&
git foo &&
test -f bar
'
This construct acts similar to test_expect_success, but instead
of reporting "ok/FAIL" like test_expect_success does, the
outcome is reported as "FIXED/still broken".
Signed-off-by: Junio C Hamano <gitster@pobox.com>
|
|
for-each-ref can accept only one quoting style. For this reason it uses
OPT_BIT for the quoting style switches so that it is easy to check for
more than one bit being set. However, not all symbolic constants were
actually single bit values. In particular:
$ git for-each-ref --python
error: more than one quoting style ?
This fixes it.
While we are here, let's also remove the space before the question mark.
Signed-off-by: Johannes Sixt <johannes.sixt@telecom.at>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
|
|
The option value for --sort is already a pointer to a pointer to struct
ref_sort, so just use it.
Signed-off-by: Lars Hjemli <hjemli@gmail.com>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
|
|
Signed-off-by: Pierre Habouzit <madcoder@debian.org>
Signed-off-by: Shawn O. Pearce <spearce@spearce.org>
|
|
Signed-off-by: Andy Parkins <andyparkins@gmail.com>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
|
Bert Wesarg
Nanako Shiraishi
Junio C Hamano
Jeff King
Johannes Sixt
Lars Hjemli
Pierre Habouzit
Andy Parkins