summaryrefslogtreecommitdiff
path: root/t/t5600-clone-fail-cleanup.sh
AgeCommit message (Collapse)AuthorFilesLines
2008-09-03tests: use "git xyzzy" form (t3600 - t6999)Libravatar Nanako Shiraishi1-6/+6
Converts tests between t3600-t6300. Signed-off-by: Nanako Shiraishi <nanako3@lavabit.com> Signed-off-by: Junio C Hamano <gitster@pobox.com>
2008-07-13t/: Use "test_must_fail git" instead of "! git"Libravatar Stephan Beyer1-2/+2
This patch changes every occurrence of "! git" -- with the meaning that a git call has to gracefully fail -- into "test_must_fail git". This is useful to - make sure the test does not fail because of a signal, e.g. SIGSEGV, and - advertise the use of "test_must_fail" for new tests. Signed-off-by: Stephan Beyer <s-beyer@gmx.net> Signed-off-by: Junio C Hamano <gitster@pobox.com>
2008-02-01Sane use of test_expect_failureLibravatar Junio C Hamano1-6/+6
Originally, test_expect_failure was designed to be the opposite of test_expect_success, but this was a bad decision. Most tests run a series of commands that leads to the single command that needs to be tested, like this: test_expect_{success,failure} 'test title' ' setup1 && setup2 && setup3 && what is to be tested ' And expecting a failure exit from the whole sequence misses the point of writing tests. Your setup$N that are supposed to succeed may have failed without even reaching what you are trying to test. The only valid use of test_expect_failure is to check a trivial single command that is expected to fail, which is a minority in tests of Porcelain-ish commands. This large-ish patch rewrites all uses of test_expect_failure to use test_expect_success and rewrites the condition of what is tested, like this: test_expect_success 'test title' ' setup1 && setup2 && setup3 && ! this command should fail ' test_expect_failure is redefined to serve as a reminder that that test *should* succeed but due to a known breakage in git it currently does not pass. So if git-foo command should create a file 'bar' but you discovered a bug that it doesn't, you can write a test like this: test_expect_failure 'git-foo should create bar' ' rm -f bar && git foo && test -f bar ' This construct acts similar to test_expect_success, but instead of reporting "ok/FAIL" like test_expect_success does, the outcome is reported as "FIXED/still broken". Signed-off-by: Junio C Hamano <gitster@pobox.com>
2007-02-03Assorted typo fixesLibravatar Pavel Roskin1-1/+1
Signed-off-by: Junio C Hamano <junkio@cox.net>
2006-10-14clone: the given repository dir should be relative to $PWDLibravatar Yasushi SHOJI1-0/+6
the repository argument for git-clone should be relative to $PWD instead of the given target directory. The old behavior gave us surprising success and you need a few minute to know why it worked. GIT_DIR is already exported so no need to cd into $D. And this makes $PWD for git-fetch-pack, which is the actual command to take the given repository dir, the same as git-clone. Signed-off-by: Yasushi SHOJI <yashi@atmark-techno.com> Signed-off-by: Junio C Hamano <junkio@cox.net>
2006-02-21New test to verify that when git-clone fails it cleans up the new directory.Libravatar Carl Worth1-0/+36
Signed-off-by: Carl Worth <cworth@cworth.org> Signed-off-by: Junio C Hamano <junkio@cox.net>