| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
>From inception, when chainlint.sed encountered a line using semicolon to
separate commands rather than `&&`, it would insert a ?!SEMI?!
annotation at the beginning of the line rather ?!AMP?! even though the
&&-chain is also broken by the semicolon. Given a line such as:
?!SEMI?! cmd1; cmd2 &&
the ?!SEMI?! annotation makes it easier to see what the problem is than
if the output had been:
?!AMP?! cmd1; cmd2 &&
which might confuse the test author into thinking that the linter is
broken (since the line clearly ends with `&&`).
However, now that the ?!AMP?! an ?!SEMI?! annotations are inserted at
the point of breakage rather than at the beginning of the line, and
taking into account that both represent a broken &&-chain, there is
little reason to distinguish between the two. Using ?!AMP?! alone is
sufficient to point the test author at the problem. For instance, in:
cmd1; ?!AMP?! cmd2 &&
cmd3
it is clear that the &&-chain is broken between `cmd1` and `cmd2`.
Likewise, in:
cmd1 && cmd2 ?!AMP?!
cmd3
it is clear that the &&-chain is broken between `cmd2` and `cmd3`.
Finally, in:
cmd1; ?!AMP?! cmd2 ?!AMP?!
cmd3
it is clear that the &&-chain is broken between each command.
Hence, there is no longer a good reason to make a distinction between a
broken &&-chain due to a semicolon and a broken chain due to a missing
`&&` at end-of-line. Therefore, drop the ?!SEMI?! annotation and use
?!AMP?! exclusively.
Signed-off-by: Eric Sunshine <sunshine@sunshineco.com>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
|
|
When chainlint.sed detects commands separated by a semicolon rather than
by `&&`, it places a ?!SEMI?! annotation at the beginning of the line.
However, this is an unusual location for programmers accustomed to error
messages (from compilers, for instance) indicating the exact point of
the problem. Therefore, relocate the ?!SEMI?! annotation to the location
of the semicolon in order to better direct the programmer's attention to
the source of the problem.
Signed-off-by: Eric Sunshine <sunshine@sunshineco.com>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
|
|
The purpose of chainlint.sed is to detect &&-chain breakage only within
subshells (one level deep); it doesn't bother checking for top-level
&&-chain breakage since the &&-chain checker built into t/test-lib.sh
should detect broken &&-chains outside of subshells by making them
magically exit with code 117.
Unfortunately, one of the chainlint.sed self-tests has overly intimate
knowledge of this particular division of responsibilities and only cares
about what chainlint.sed itself will produce, while ignoring the fact
that a more all-encompassing linter would complain about a broken
&&-chain outside the subshell. This makes it difficult to re-use the
test with a more capable chainlint implementation should one ever be
developed. Therefore, adjust the test and its "expected" output to
avoid being specific to the tunnel-vision of this one implementation.
Signed-off-by: Eric Sunshine <sunshine@sunshineco.com>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
|
|
The --chain-lint option uses heuristics and knowledge of shell syntax to
detect broken &&-chains in subshells by pure textual inspection. The
heuristics handle a range of stylistic variations in existing tests
(evolved over the years), however, they are still best-guesses. As such,
it is possible for future changes to accidentally break assumptions upon
which the heuristics are based. Protect against this possibility by
adding tests which check the linter itself for correctness.
In addition to protecting against regressions, these tests help document
(for humans) expected behavior, which is important since the linter's
implementation language ('sed') does not necessarily lend itself to easy
comprehension.
Signed-off-by: Eric Sunshine <sunshine@sunshineco.com>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
|
Eric Sunshine