summaryrefslogtreecommitdiff
path: root/t/README
diff options
context:
space:
mode:
Diffstat (limited to 't/README')
-rw-r--r--t/README115
1 files changed, 110 insertions, 5 deletions
diff --git a/t/README b/t/README
index caeeb9dedc..d5bb0c9aa1 100644
--- a/t/README
+++ b/t/README
@@ -71,6 +71,7 @@ You can pass --verbose (or -v), --debug (or -d), and --immediate
(or -i) command line argument to the test, or by setting GIT_TEST_OPTS
appropriately before running "make".
+-v::
--verbose::
This makes the test more verbose. Specifically, the
command being run and their output if any are also
@@ -81,6 +82,13 @@ appropriately before running "make".
numbers matching <pattern>. The number matched against is
simply the running count of the test within the file.
+-x::
+ Turn on shell tracing (i.e., `set -x`) during the tests
+ themselves. Implies `--verbose`. Note that this can cause
+ failures in some tests which redirect and test the
+ output of shell functions. Use with caution.
+
+-d::
--debug::
This may help the person who is developing a new test.
It causes the command defined with test_debug to run.
@@ -89,6 +97,7 @@ appropriately before running "make".
failed tests so that you can inspect its contents after
the test finished.
+-i::
--immediate::
This causes the test to immediately exit upon the first
failed test. Cleanup commands requested with
@@ -96,10 +105,17 @@ appropriately before running "make".
in order to keep the state for inspection by the tester
to diagnose the bug.
+-l::
--long-tests::
This causes additional long-running tests to be run (where
available), for more exhaustive testing.
+-r::
+--run=<test-selector>::
+ Run only the subset of tests indicated by
+ <test-selector>. See section "Skipping Tests" below for
+ <test-selector> syntax.
+
--valgrind=<tool>::
Execute all Git binaries under valgrind tool <tool> and exit
with status 126 on errors (just like regular tests, this will
@@ -187,10 +203,77 @@ and either can match the "t[0-9]{4}" part to skip the whole
test, or t[0-9]{4} followed by ".$number" to say which
particular test to skip.
-Note that some tests in the existing test suite rely on previous
-test item, so you cannot arbitrarily disable one and expect the
-remainder of test to check what the test originally was intended
-to check.
+For an individual test suite --run could be used to specify that
+only some tests should be run or that some tests should be
+excluded from a run.
+
+The argument for --run is a list of individual test numbers or
+ranges with an optional negation prefix that define what tests in
+a test suite to include in the run. A range is two numbers
+separated with a dash and matches a range of tests with both ends
+been included. You may omit the first or the second number to
+mean "from the first test" or "up to the very last test"
+respectively.
+
+Optional prefix of '!' means that the test or a range of tests
+should be excluded from the run.
+
+If --run starts with an unprefixed number or range the initial
+set of tests to run is empty. If the first item starts with '!'
+all the tests are added to the initial set. After initial set is
+determined every test number or range is added or excluded from
+the set one by one, from left to right.
+
+Individual numbers or ranges could be separated either by a space
+or a comma.
+
+For example, to run only tests up to a specific test (21), one
+could do this:
+
+ $ sh ./t9200-git-cvsexport-commit.sh --run='1-21'
+
+or this:
+
+ $ sh ./t9200-git-cvsexport-commit.sh --run='-21'
+
+Common case is to run several setup tests (1, 2, 3) and then a
+specific test (21) that relies on that setup:
+
+ $ sh ./t9200-git-cvsexport-commit.sh --run='1 2 3 21'
+
+or:
+
+ $ sh ./t9200-git-cvsexport-commit.sh --run=1,2,3,21
+
+or:
+
+ $ sh ./t9200-git-cvsexport-commit.sh --run='-3 21'
+
+As noted above, the test set is built going though items left to
+right, so this:
+
+ $ sh ./t9200-git-cvsexport-commit.sh --run='1-4 !3'
+
+will run tests 1, 2, and 4. Items that comes later have higher
+precendence. It means that this:
+
+ $ sh ./t9200-git-cvsexport-commit.sh --run='!3 1-4'
+
+would just run tests from 1 to 4, including 3.
+
+You may use negation with ranges. The following will run all
+test in the test suite except from 7 up to 11:
+
+ $ sh ./t9200-git-cvsexport-commit.sh --run='!7-11'
+
+Some tests in a test suite rely on the previous tests performing
+certain actions, specifically some tests are designated as
+"setup" test, so you cannot _arbitrarily_ disable one test and
+expect the rest to function correctly.
+
+--run is mostly useful when you want to focus on a specific test
+and know what setup is needed for it. Or when you want to run
+everything up to a certain test.
Naming Tests
@@ -335,7 +418,8 @@ Don't:
dies in an unexpected way (e.g. segfault).
On the other hand, don't use test_must_fail for running regular
- platform commands; just use '! cmd'.
+ platform commands; just use '! cmd'. We are not in the business
+ of verifying that the world given to us sanely works.
- use perl without spelling it as "$PERL_PATH". This is to help our
friends on Windows where the platform Perl often adds CR before
@@ -596,6 +680,27 @@ library for your script to use.
...
'
+ - test_write_lines <lines>
+
+ Write <lines> on standard output, one line per argument.
+ Useful to prepare multi-line files in a compact form.
+
+ Example:
+
+ test_write_lines a b c d e f g >foo
+
+ Is a more compact equivalent of:
+ cat >foo <<-EOF
+ a
+ b
+ c
+ d
+ e
+ f
+ g
+ EOF
+
+
- test_pause
This command is useful for writing and debugging tests and must be