diff options
Diffstat (limited to 't/README')
| -rw-r--r-- | t/README | 81 |
1 files changed, 72 insertions, 9 deletions
@@ -84,9 +84,10 @@ appropriately before running "make". -x:: Turn on shell tracing (i.e., `set -x`) during the tests - themselves. Implies `--verbose`. Note that in non-bash shells, - this can cause failures in some tests which redirect and test - the output of shell functions. Use with caution. + themselves. Implies `--verbose`. + Ignored in test scripts that set the variable 'test_untraceable' + to a non-empty value, unless it's run with a Bash version + supporting BASH_XTRACEFD, i.e. v4.1 or later. -d:: --debug:: @@ -292,6 +293,28 @@ and know what setup is needed for it. Or when you want to run everything up to a certain test. +Running tests with special setups +--------------------------------- + +The whole test suite could be run to test some special features +that cannot be easily covered by a few specific test cases. These +could be enabled by running the test suite with correct GIT_TEST_ +environment set. + +GIT_TEST_SPLIT_INDEX=<boolean> forces split-index mode on the whole +test suite. Accept any boolean values that are accepted by git-config. + +GIT_TEST_FULL_IN_PACK_ARRAY=<boolean> exercises the uncommon +pack-objects code path where there are more than 1024 packs even if +the actual number of packs in repository is below this limit. Accept +any boolean values that are accepted by git-config. + +GIT_TEST_OE_SIZE=<n> exercises the uncommon pack-objects code path +where we do not cache object size in memory and read it from existing +packs on demand. This normally only happens when the object size is +over 2GB. This variable forces the code path on any object larger than +<n> bytes. + Naming Tests ------------ @@ -332,13 +355,10 @@ Writing Tests ------------- The test script is written as a shell script. It should start -with the standard "#!/bin/sh" with copyright notices, and an +with the standard "#!/bin/sh", and an assignment to variable 'test_description', like this: #!/bin/sh - # - # Copyright (c) 2005 Junio C Hamano - # test_description='xxx test (option --frotz) @@ -455,6 +475,22 @@ Don't: causing the next test to start in an unexpected directory. Do so inside a subshell if necessary. + - save and verify the standard error of compound commands, i.e. group + commands, subshells, and shell functions (except test helper + functions like 'test_must_fail') like this: + + ( cd dir && git cmd ) 2>error && + test_cmp expect error + + When running the test with '-x' tracing, then the trace of commands + executed in the compound command will be included in standard error + as well, quite possibly throwing off the subsequent checks examining + the output. Instead, save only the relevant git command's standard + error: + + ( cd dir && git cmd 2>../error ) && + test_cmp expect error + - Break the TAP output The raw output from your test may be interpreted by a TAP harness. TAP @@ -658,7 +694,7 @@ library for your script to use. test_expect_code 1 git merge "merge msg" B master ' - - test_must_fail <git-command> + - test_must_fail [<options>] <git-command> Run a git command and ensure it fails in a controlled way. Use this instead of "! <git-command>". When git-command dies due to a @@ -666,17 +702,32 @@ library for your script to use. treats it as just another expected failure, which would let such a bug go unnoticed. - - test_might_fail <git-command> + Accepts the following options: + + ok=<signal-name>[,<...>]: + Don't treat an exit caused by the given signal as error. + Multiple signals can be specified as a comma separated list. + Currently recognized signal names are: sigpipe, success. + (Don't use 'success', use 'test_might_fail' instead.) + + - test_might_fail [<options>] <git-command> Similar to test_must_fail, but tolerate success, too. Use this instead of "<git-command> || :" to catch failures due to segv. + Accepts the same options as test_must_fail. + - test_cmp <expected> <actual> Check whether the content of the <actual> file matches the <expected> file. This behaves like "cmp" but produces more helpful output when the test is run with "-v" option. + - test_cmp_rev <expected> <actual> + + Check whether the <expected> rev points to the same commit as the + <actual> rev. + - test_line_count (= | -lt | -ge | ...) <length> <file> Check whether a file has the length it is expected to. @@ -808,6 +859,18 @@ use these, and "test_set_prereq" for how to define your own. Git was compiled with support for PCRE. Wrap any tests that use git-grep --perl-regexp or git-grep -P in these. + - LIBPCRE1 + + Git was compiled with PCRE v1 support via + USE_LIBPCRE1=YesPlease. Wrap any PCRE using tests that for some + reason need v1 of the PCRE library instead of v2 in these. + + - LIBPCRE2 + + Git was compiled with PCRE v2 support via + USE_LIBPCRE2=YesPlease. Wrap any PCRE using tests that for some + reason need v2 of the PCRE library instead of v1 in these. + - CASE_INSENSITIVE_FS Test is run on a case insensitive file system. |