diff options
Diffstat (limited to 'Documentation/pretty-formats.txt')
| -rw-r--r-- | Documentation/pretty-formats.txt | 51 |
1 files changed, 38 insertions, 13 deletions
diff --git a/Documentation/pretty-formats.txt b/Documentation/pretty-formats.txt index 671cebd95c..e664c088a5 100644 --- a/Documentation/pretty-formats.txt +++ b/Documentation/pretty-formats.txt @@ -143,12 +143,24 @@ ifndef::git-rev-list[] - '%N': commit notes endif::git-rev-list[] - '%GG': raw verification message from GPG for a signed commit -- '%G?': show "G" for a Good signature, "B" for a Bad signature, "U" for a good, - untrusted signature and "N" for no signature +- '%G?': show "G" for a good (valid) signature, + "B" for a bad signature, + "U" for a good signature with unknown validity, + "X" for a good signature that has expired, + "Y" for a good signature made by an expired key, + "R" for a good signature made by a revoked key, + "E" if the signature cannot be checked (e.g. missing key) + and "N" for no signature - '%GS': show the name of the signer for a signed commit - '%GK': show the key used to sign a signed commit -- '%gD': reflog selector, e.g., `refs/stash@{1}` -- '%gd': shortened reflog selector, e.g., `stash@{1}` +- '%gD': reflog selector, e.g., `refs/stash@{1}` or + `refs/stash@{2 minutes ago`}; the format follows the rules described + for the `-g` option. The portion before the `@` is the refname as + given on the command line (so `git log -g refs/heads/master` would + yield `refs/heads/master@{0}`). +- '%gd': shortened reflog selector; same as `%gD`, but the refname + portion is shortened for human readability (so `refs/heads/master` + becomes just `master`). - '%gn': reflog identity name - '%gN': reflog identity name (respecting .mailmap, see linkgit:git-shortlog[1] or linkgit:git-blame[1]) @@ -160,13 +172,19 @@ endif::git-rev-list[] - '%Cgreen': switch color to green - '%Cblue': switch color to blue - '%Creset': reset color -- '%C(...)': color specification, as described in color.branch.* config option; - adding `auto,` at the beginning will emit color only when colors are - enabled for log output (by `color.diff`, `color.ui`, or `--color`, and - respecting the `auto` settings of the former if we are going to a - terminal). `auto` alone (i.e. `%C(auto)`) will turn on auto coloring - on the next placeholders until the color is switched again. -- '%m': left, right or boundary mark +- '%C(...)': color specification, as described under Values in the + "CONFIGURATION FILE" section of linkgit:git-config[1]. + By default, colors are shown only when enabled for log output (by + `color.diff`, `color.ui`, or `--color`, and respecting the `auto` + settings of the former if we are going to a terminal). `%C(auto,...)` + is accepted as a historical synonym for the default (e.g., + `%C(auto,red)`). Specifying `%C(always,...) will show the colors + even when color is not otherwise enabled (though consider + just using `--color=always` to enable color for the whole output, + including this format and anything else git might color). `auto` + alone (i.e. `%C(auto)`) will turn on auto coloring on the next + placeholders until the color is switched again. +- '%m': left (`<`), right (`>`) or boundary (`-`) mark - '%n': newline - '%%': a raw '%' - '%x00': print a byte from a hex code @@ -186,6 +204,13 @@ endif::git-rev-list[] than given and there are spaces on its left, use those spaces - '%><(<N>)', '%><|(<N>)': similar to '% <(<N>)', '%<|(<N>)' respectively, but padding both sides (i.e. the text is centered) +- %(trailers[:options]): display the trailers of the body as interpreted + by linkgit:git-interpret-trailers[1]. The `trailers` string may be + followed by a colon and zero or more comma-separated options. If the + `only` option is given, omit non-trailer lines from the trailer block. + If the `unfold` option is given, behave as if interpret-trailer's + `--unfold` option was given. E.g., `%(trailers:only,unfold)` to do + both. NOTE: Some placeholders may depend on other options given to the revision traversal engine. For example, the `%g*` reflog options will @@ -198,8 +223,8 @@ If you add a `+` (plus sign) after '%' of a placeholder, a line-feed is inserted immediately before the expansion if and only if the placeholder expands to a non-empty string. -If you add a `-` (minus sign) after '%' of a placeholder, line-feeds that -immediately precede the expansion are deleted if and only if the +If you add a `-` (minus sign) after '%' of a placeholder, all consecutive +line-feeds immediately preceding the expansion are deleted if and only if the placeholder expands to an empty string. If you add a ` ` (space) after '%' of a placeholder, a space |