diff options
Diffstat (limited to 'Documentation/diff-options.txt')
| -rw-r--r-- | Documentation/diff-options.txt | 261 |
1 files changed, 214 insertions, 47 deletions
diff --git a/Documentation/diff-options.txt b/Documentation/diff-options.txt index 8707d0e740..9f7cba2be6 100644 --- a/Documentation/diff-options.txt +++ b/Documentation/diff-options.txt @@ -21,6 +21,7 @@ endif::git-format-patch[] ifndef::git-format-patch[] -p:: -u:: +--patch:: Generate patch (see section on generating patches). {git-diff? This is the default.} endif::git-format-patch[] @@ -44,14 +45,24 @@ ifndef::git-format-patch[] Synonym for `-p --raw`. endif::git-format-patch[] +--minimal:: + Spend extra time to make sure the smallest possible + diff is produced. + --patience:: Generate a diff using the "patience diff" algorithm. ---stat[=width[,name-width]]:: +--stat[=<width>[,<name-width>[,<count>]]]:: Generate a diffstat. You can override the default - output width for 80-column terminal by `--stat=width`. + output width for 80-column terminal by `--stat=<width>`. The width of the filename part can be controlled by giving another width to it separated by a comma. + By giving a third parameter `<count>`, you can limit the + output to the first `<count>` lines, followed by + `...` if there are more. ++ +These parameters can also be set individually with `--stat-width=<width>`, +`--stat-name-width=<name-width>` and `--stat-count=<count>`. --numstat:: Similar to `\--stat`, but shows number of added and @@ -65,15 +76,49 @@ endif::git-format-patch[] number of modified files, as well as number of added and deleted lines. ---dirstat[=limit]:: - Output the distribution of relative amount of changes (number of lines added or - removed) for each sub-directory. Directories with changes below - a cut-off percent (3% by default) are not shown. The cut-off percent - can be set with `--dirstat=limit`. Changes in a child directory is not - counted for the parent directory, unless `--cumulative` is used. - ---dirstat-by-file[=limit]:: - Same as `--dirstat`, but counts changed files instead of lines. +--dirstat[=<param1,param2,...>]:: + Output the distribution of relative amount of changes for each + sub-directory. The behavior of `--dirstat` can be customized by + passing it a comma separated list of parameters. + The defaults are controlled by the `diff.dirstat` configuration + variable (see linkgit:git-config[1]). + The following parameters are available: ++ +-- +`changes`;; + Compute the dirstat numbers by counting the lines that have been + removed from the source, or added to the destination. This ignores + the amount of pure code movements within a file. In other words, + rearranging lines in a file is not counted as much as other changes. + This is the default behavior when no parameter is given. +`lines`;; + Compute the dirstat numbers by doing the regular line-based diff + analysis, and summing the removed/added line counts. (For binary + files, count 64-byte chunks instead, since binary files have no + natural concept of lines). This is a more expensive `--dirstat` + behavior than the `changes` behavior, but it does count rearranged + lines within a file as much as other changes. The resulting output + is consistent with what you get from the other `--*stat` options. +`files`;; + Compute the dirstat numbers by counting the number of files changed. + Each changed file counts equally in the dirstat analysis. This is + the computationally cheapest `--dirstat` behavior, since it does + not have to look at the file contents at all. +`cumulative`;; + Count changes in a child directory for the parent directory as well. + Note that when using `cumulative`, the sum of the percentages + reported may exceed 100%. The default (non-cumulative) behavior can + be specified with the `noncumulative` parameter. +<limit>;; + An integer parameter specifies a cut-off percent (3% by default). + Directories contributing less than this percentage of the changes + are not shown in the output. +-- ++ +Example: The following will count changed files, while ignoring +directories with less than 10% of the total amount of changed files, +and accumulating child directory counts in the parent directories: +`--dirstat=files,10,cumulative`. --summary:: Output a condensed summary of extended header information @@ -94,8 +139,8 @@ Also, when `--raw` or `--numstat` has been given, do not munge pathnames and use NULs as output field terminators. endif::git-log[] ifndef::git-log[] - When `--raw` or `--numstat` has been given, do not munge - pathnames and use NULs as output field terminators. + When `--raw`, `--numstat`, `--name-only` or `--name-status` has been + given, do not munge pathnames and use NULs as output field terminators. endif::git-log[] + Without this option, each pathname output will have TAB, LF, double quotes, @@ -117,18 +162,55 @@ any of those replacements occurred. option and lists the commits in that commit range like the 'summary' option of linkgit:git-submodule[1] does. ---color:: +--color[=<when>]:: Show colored diff. + The value must be `always` (the default for `<when>`), `never`, or `auto`. + The default value is `never`. +ifdef::git-diff[] + It can be changed by the `color.ui` and `color.diff` + configuration settings. +endif::git-diff[] --no-color:: - Turn off colored diff, even when the configuration file - gives the default to color output. + Turn off colored diff. +ifdef::git-diff[] + This can be used to override configuration settings. +endif::git-diff[] + It is the same as `--color=never`. ---color-words[=<regex>]:: - Show colored word diff, i.e., color words which have changed. - By default, words are separated by whitespace. +--word-diff[=<mode>]:: + Show a word diff, using the <mode> to delimit changed words. + By default, words are delimited by whitespace; see + `--word-diff-regex` below. The <mode> defaults to 'plain', and + must be one of: ++ +-- +color:: + Highlight changed words using only colors. Implies `--color`. +plain:: + Show words as `[-removed-]` and `{+added+}`. Makes no + attempts to escape the delimiters if they appear in the input, + so the output may be ambiguous. +porcelain:: + Use a special line-based format intended for script + consumption. Added/removed/unchanged runs are printed in the + usual unified diff format, starting with a `+`/`-`/` ` + character at the beginning of the line and extending to the + end of the line. Newlines in the input are represented by a + tilde `~` on a line of its own. +none:: + Disable word diff again. +-- ++ +Note that despite the name of the first mode, color is used to +highlight the changed parts in all modes if enabled. + +--word-diff-regex=<regex>:: + Use <regex> to decide what a word is, instead of considering + runs of non-whitespace to be a word. Also implies + `--word-diff` unless it was already enabled. + -When a <regex> is specified, every non-overlapping match of the +Every non-overlapping match of the <regex> is considered a word. Anything between these matches is considered whitespace and ignored(!) for the purposes of finding differences. You may want to append `|[^[:space:]]` to your regular @@ -140,6 +222,10 @@ The regex can also be set via a diff driver or configuration option, see linkgit:gitattributes[1] or linkgit:git-config[1]. Giving it explicitly overrides any diff driver or configuration setting. Diff drivers override configuration settings. + +--color-words[=<regex>]:: + Equivalent to `--word-diff=color` plus (if a regex was + specified) `--word-diff-regex=<regex>`. endif::git-format-patch[] --no-renames:: @@ -148,10 +234,14 @@ endif::git-format-patch[] ifndef::git-format-patch[] --check:: - Warn if changes introduce trailing whitespace - or an indent that uses a space before a tab. Exits with - non-zero status if problems are found. Not compatible with - --exit-code. + Warn if changes introduce whitespace errors. What are + considered whitespace errors is controlled by `core.whitespace` + configuration. By default, trailing whitespaces (including + lines that solely consist of whitespaces) and a space character + that is immediately followed by a tab character inside the + initial indent of the line are considered whitespace errors. + Exits with non-zero status if problems are found. Not compatible + with --exit-code. endif::git-format-patch[] --full-index:: @@ -171,28 +261,49 @@ endif::git-format-patch[] the diff-patch output format. Non default number of digits can be specified with `--abbrev=<n>`. --B:: - Break complete rewrite changes into pairs of delete and create. - --M:: +-B[<n>][/<m>]:: +--break-rewrites[=[<n>][/<m>]]:: + Break complete rewrite changes into pairs of delete and + create. This serves two purposes: ++ +It affects the way a change that amounts to a total rewrite of a file +not as a series of deletion and insertion mixed together with a very +few lines that happen to match textually as the context, but as a +single deletion of everything old followed by a single insertion of +everything new, and the number `m` controls this aspect of the -B +option (defaults to 60%). `-B/70%` specifies that less than 30% of the +original should remain in the result for git to consider it a total +rewrite (i.e. otherwise the resulting patch will be a series of +deletion and insertion mixed together with context lines). ++ +When used with -M, a totally-rewritten file is also considered as the +source of a rename (usually -M only considers a file that disappeared +as the source of a rename), and the number `n` controls this aspect of +the -B option (defaults to 50%). `-B20%` specifies that a change with +addition and deletion compared to 20% or more of the file's size are +eligible for being picked up as a possible source of a rename to +another file. + +-M[<n>]:: +--find-renames[=<n>]:: +ifndef::git-log[] Detect renames. - --C:: +endif::git-log[] +ifdef::git-log[] + If generating diffs, detect and report renames for each commit. + For following files across renames while traversing history, see + `--follow`. +endif::git-log[] + If `n` is specified, it is a threshold on the similarity + index (i.e. amount of addition/deletions compared to the + file's size). For example, `-M90%` means git should consider a + delete/add pair to be a rename if more than 90% of the file + hasn't changed. + +-C[<n>]:: +--find-copies[=<n>]:: Detect copies as well as renames. See also `--find-copies-harder`. - -ifndef::git-format-patch[] ---diff-filter=[ACDMRTUXB*]:: - Select only files that are Added (`A`), Copied (`C`), - Deleted (`D`), Modified (`M`), Renamed (`R`), have their - type (i.e. regular file, symlink, submodule, ...) changed (`T`), - are Unmerged (`U`), are - Unknown (`X`), or have had their pairing Broken (`B`). - Any combination of the filter characters may be used. - When `*` (All-or-none) is added to the combination, all - paths are selected if there is any file that matches - other criteria in the comparison; if there is no file - that matches other criteria, nothing is selected. -endif::git-format-patch[] + If `n` is specified, it has the same meaning as for `-M<n>`. --find-copies-harder:: For performance reasons, by default, `-C` option finds copies only @@ -203,6 +314,19 @@ endif::git-format-patch[] projects, so use it with caution. Giving more than one `-C` option has the same effect. +-D:: +--irreversible-delete:: + Omit the preimage for deletes, i.e. print only the header but not + the diff between the preimage and `/dev/null`. The resulting patch + is not meant to be applied with `patch` nor `git apply`; this is + solely for people who want to just concentrate on reviewing the + text after the change. In addition, the output obviously lack + enough information to apply such a patch in reverse, even manually, + hence the name of the option. ++ +When used together with `-B`, omit also the preimage in the deletion part +of a delete/create pair. + -l<num>:: The `-M` and `-C` options require O(n^2) processing time where n is the number of potential rename/copy targets. This @@ -211,14 +335,30 @@ endif::git-format-patch[] number. ifndef::git-format-patch[] +--diff-filter=[(A|C|D|M|R|T|U|X|B)...[*]]:: + Select only files that are Added (`A`), Copied (`C`), + Deleted (`D`), Modified (`M`), Renamed (`R`), have their + type (i.e. regular file, symlink, submodule, ...) changed (`T`), + are Unmerged (`U`), are + Unknown (`X`), or have had their pairing Broken (`B`). + Any combination of the filter characters (including none) can be used. + When `*` (All-or-none) is added to the combination, all + paths are selected if there is any file that matches + other criteria in the comparison; if there is no file + that matches other criteria, nothing is selected. + -S<string>:: Look for differences that introduce or remove an instance of <string>. Note that this is different than the string simply appearing in diff output; see the 'pickaxe' entry in linkgit:gitdiffcore[7] for more details. +-G<regex>:: + Look for differences whose added or removed line matches + the given <regex>. + --pickaxe-all:: - When `-S` finds a change, show all the changes in that + When `-S` or `-G` finds a change, show all the changes in that changeset, not just the files that contain the change in <string>. @@ -268,7 +408,12 @@ endif::git-format-patch[] Show the context between diff hunks, up to the specified number of lines, thereby fusing hunks that are close to each other. +-W:: +--function-context:: + Show whole surrounding functions of changes. + ifndef::git-format-patch[] +ifndef::git-log[] --exit-code:: Make the program exit with codes similar to diff(1). That is, it exits with 1 if there were differences and @@ -276,6 +421,7 @@ ifndef::git-format-patch[] --quiet:: Disable all output of the program. Implies `--exit-code`. +endif::git-log[] endif::git-format-patch[] --ext-diff:: @@ -286,8 +432,29 @@ endif::git-format-patch[] --no-ext-diff:: Disallow external diff drivers. ---ignore-submodules:: - Ignore changes to submodules in the diff generation. +--textconv:: +--no-textconv:: + Allow (or disallow) external text conversion filters to be run + when comparing binary files. See linkgit:gitattributes[5] for + details. Because textconv filters are typically a one-way + conversion, the resulting diff is suitable for human + consumption, but cannot be applied. For this reason, textconv + filters are enabled by default only for linkgit:git-diff[1] and + linkgit:git-log[1], but not for linkgit:git-format-patch[1] or + diff plumbing commands. + +--ignore-submodules[=<when>]:: + Ignore changes to submodules in the diff generation. <when> can be + either "none", "untracked", "dirty" or "all", which is the default + Using "none" will consider the submodule modified when it either contains + untracked or modified files or its HEAD differs from the commit recorded + in the superproject and can be used to override any settings of the + 'ignore' option in linkgit:git-config[1] or linkgit:gitmodules[5]. When + "untracked" is used submodules are not considered dirty when they only + contain untracked content (but they are still scanned for modified + content). Using "dirty" ignores all changes to the work tree of submodules, + only changes to the commits stored in the superproject are shown (this was + the behavior until 1.7.0). Using "all" hides all changes to submodules. --src-prefix=<prefix>:: Show the given source prefix instead of "a/". |